Posts filed under ‘General Mold Information’

How Things Went from Bad to Worse: A Client’s Story

leaking roof

We performed a mold assessment for a family whose home experienced significant water intrusion in November of 2015.  Our clients were in the process of having their roof replaced when a fast moving storm came in just after their old roof had been torn off.  The roofing company installed tarps on the unfinished areas of the roof, but the high winds blew them off, subjecting the home to a significant amount of water intrusion.  The water ran down the ceiling beams, into the walls and saturated their floors, furniture, electronics and other personal items.  The roofing contractor wanted to avoid a claim on his business insurance policy, so he told the homeowners that he knew how to dry out the house and he would take care of it.  He brought in a heater and a couple of fans and instructed our clients to turn up the heat in their home.  Our client trusted that the roofing contractor indeed knew how to dry out their home properly and they followed his instructions hoping the dry out would be successful.
Unfortunately, not only was the dry out unsuccessful, but the newly installed roof leaked a couple of months after installation, causing water intrusion for the second time.  At that point, our client filed a claim with their insurance company to try to get the situation handled properly.  During this time, the family had multiple unexplained health issues that they now believe were most likely due to microbial conditions that occurred after the water intrusions.  Their daughter started to get sick frequently and experienced sinus issues, nose bleeds, burning and itching eyes, headaches, and burning throat conditions.  She also was told to use a nebulizer due to her asthmatic condition.  Her mother was perplexed by this because her daughter has had asthma for several years that had been controlled up until this time and she had never needed to use a nebulizer.  Other family members also started experiencing unusual symptoms during this time.

After filing their insurance claim, the insurance company sent out a water restoration company to dry out the home.  Our clients were told that the home was now dry and everything was fine.  Our clients were highly concerned because the suspected that the walls were not adequately dry and they were not confident that the roof issues had been permanently corrected.  So, they brought in a water restoration company and a different roofing contractor for an unbiased opinion.  It was determined that there were still wet building materials within the home and they suspected an even bigger problem, hidden mold growth within the walls and under flooring materials.  This is where Mold Inspection Sciences came in.

After a full assessment and laboratory testing, we confirmed that the Living Room wall was still actively wet, mold growth was present in multiple areas within the home and ambient air testing of the lower level showed elevated airborne mold spore counts when compared to the outside control sample.  Sadly, after following up with our client, she stated “my husband came down with a headache that was so intense he could not move, his throat and eyes burned, he felt sick and very tired, then he started to have problems remembering what was just said to him – he got extreme brain fog”.

At this time, our clients are still working to come to a resolution with their insurance company, but for now, they have had to leave their home until proper mold remediation can be performed.

Mold Inspection Sciences was honored to help this family and we sincerely hope that their health improves and they are able to be back into their home very soon.

Craig Cooper

by Craig Cooper, Mold Inspection Sciences

June 22, 2016 at 10:44 am

What If There’s mold On My belongings?

Moldy Furniture
Many times when clients’ tests come back positive for mold growth, the next concern typically is “I think mold may be on my belongings. Can I get rid of the mold or do I have to throw my belongings away?”

The small porous stuff (such as clothing, stuffed animals, bedding, etc.) can easily be washed. You can use your choice of vinegar, bleach, Borax, tea tree oil, or whatever other cleaning agent. But the items need to be washed on the hottest setting possible and permissible. Then hang the items in the sun while still wet to help get rid of germs and odors and to fade any staining.

For small non-porous items (such as toys, dishes, the shower door, etc.), a little elbow grease, some hot water, and your preferred cleaning agent will do the trick. You may even place the item in the dishwasher (remember you can put larger items in by taking out the upper rack). Be sure to thoroughly dry the items with a well-absorbing towel, well-circulating air, or even in the sun.

As far as larger items go, there are a few different options. The first option is to break the item down to try to put items into the washing machine and use a little elbow grease where necessary. Another option is to hire a restoration company to clean the items. You may want to get valuable furniture reupholstered. And if the item is not worth the time or money to clean, simply replace it.

All in all, belongings can be salvaged with proper cleaning. It may take some time and patience, but mold doesn’t mean you need to throw everything away.

Heidi Aspedon

Heidi Aspedon, Customer Service Representative

June 8, 2016 at 11:35 am

September, 2013 – Colorado Flood Series Part II

Flatirons

I wanted to start our series by discussing the different ways in which homes and businesses were affected by the moisture. A lot of situations were unique, but I think we can summarize them into three main categories, the first being rainwater:

Many structures were affected by the rainwater directly. What I mean by that is the actual water falling from the sky. From September 9th through September 16th, 17.15 inches of rain fell in the Boulder area, over 9 inches of that total was on Thursday, September 12th alone. We saw a lot of homes that were affected by roof leaks, leaks at doors and windows, and water intrusion issues at siding and wall coverings. Many of these homes had never had a previous issue, but with the amount of water that fell in such a short amount of time overwhelmed some systems. We also saw similar conditions in homes where there may have been a very small issue prior to the storm, but had not yet become readily visible or known. But once the rains came, it quickly became apparent.

Be sure to check back in for the next entry in which we will discuss how groundwater seepage affected many homes.

Brandon Apple

by Brandon Apple, Mold Inspection Sciences

March 14, 2014 at 2:08 pm

September, 2013 – Colorado Flood Series

Flatirons

In early September of 2013, Colorado was struck by intense rains and flooding. It was a once in a lifetime event (or at least we hope) for most of us who were present and witnessed the events first hand. The National Weather Service sure seems to think so, calling the storm a once-in-a-millennium event. Rains fell almost continuously from September 9th to September 15th, and as a result natural waterways and manmade water control systems were overwhelmed, causing widespread damage. Many parts of the state were affected in varying degrees, but perhaps the most densely populated area affected, and therefore one of the hardest hit was Boulder County, CO.

Boulder just happens to be one of the locations where Mold Inspection Sciences has called home for many years, where I work as one of the Lead Project Managers. The company has been around since 2002, and has been serving the Boulder community for a large part of that time. The owner is actually a current resident of Boulder and graduate of CU. We specialize in coming in as an independent, 3rd party consultant in situations where water and/or mold have impacted homes and businesses. It is our goal to identify if problems exist, if so what caused them, provide proper cleaning and restoration recommendations to address the issues, and then ensure that any necessary cleanup work was performed properly. So, when the September disaster occurred, we were here to help as many CO residents as we could. Because we were on the front lines, we saw the different ways in which people’s home were affected by the moisture, how people dealt with the issues they were confronted with, and what people can expect to see in the long run in regards to homes that were previously affected.

Please stay tuned for the next part in the series in which we will start discussing the different ways in which homes and businesses were affected by the moisture.

Brandon Apple

by Brandon Apple, Mold Inspection Sciences

February 27, 2014 at 11:42 am

Mold Sampling

mold-testing-zefon-bio-pumpA complete mold investigation typically consists of two parts, 1) the physical investigation and 2) the collection of microbial samples (mold sampling). The physical investigation should be performed by a certified microbial investigator who not only takes into account the visual evidence but also uses specialized moisture detection equipment in an effort to understand conditions throughout the home. Then, based on the findings of the physical inspection, microbial samples are collected and analyzed. The samples aid in determining if hidden mold sources exist, determining the extent of contamination, and definitively showing what types of molds are impacting a home.

There are many different types of microbial samples that can be collected, but the most helpful and commonly used are surface sampling, ambient air sampling and wall cavity sampling. Appropriate samples are recommended and collected based on the physical conditions found during the inspection, and are then sent to a certified laboratory to be analyzed.

Surface Sampling – Surface sampling is useful first off to positively identify suspect materials as mold. Mold’s appearance can be similar to common household materials such as lint, dirt and staining, therefore positively identifying suspect materials is important. Additionally, surface sampling will determine the type(s) of mold that are present. For the most part, any mold growth within a home is a bad thing. However, there are certain types of molds (under certain physical conditions and when caused by certain sources of moisture) that do not require professional remediation (removal) and can be dealt with through normal housecleaning techniques. So when you consider that having a surface sample could mean the difference between spending thousands of dollars on remediation, or instead just pulling out a washcloth and getting a little dirty, a single surface sample starts to make a lot of sense. Surface samples are collected in one of three ways:

1) Swab Sample –Swab sample media is in simple terms a sanitary Q-Tip. It is a rod that has a cotton-like media on the end of it. The media is rolled or pushed into the suspect material and the porous nature of the media collects the suspect material. This is then placed in a sealed container with a specialized fluid inside to preserve the sample.
2) Tape Lift Sample – Tape lift samples are pretty much what they sound like. It is a plastic or glass clear slide that has an adhesive on one side of it. This is placed on the suspect material and it is captured in a mirror image of its natural state. This is then placed in a closed case for protection.
3) Bulk Sample – Bulk sampling is actually the preferred method of surface sampling, but is not always feasible. Bulk sampling is where an actual piece of the impacted material is removed and used for the analysis. It is preferred because the suspect material is undisturbed from its natural state on its growth media and as a result provides the most accurate findings. It is not always feasible though because in some cases it may mean the removal or demolition of finished building materials such as drywall or baseboards for example.

Ambient Air Sampling – Air sampling is utilized in many different scenarios. It identifies the presence, types and quantities of airborne mold spores in the area where it was collected. This is done by pulling a metered amount of air through a spore trap, which will collect any particulate within the air including microscopic mold spores. All indoor samples are compared to an outdoor control or baseline sample to determine if the indoor conditions are excessive or “elevated”. This sampling method is useful in determining the overall air quality in a space specific to mold spores, determining the overall extent of contamination in an impacted space, and is also used as an indicator to help determine if hidden mold sources are present.

Wall Cavity Sampling – Wall cavity sampling is useful in determining if hidden mold sources exist within inaccessible spaces of home such as within walls or ceiling cavities. It is collected using the same methods of an ambient air sample, but only air from within the cavity in question is pulled through the spore trap. This is done by making a small hole in the wall (usually about 3/8”), inserting a sanitary wall cavity tube into the hole, and then connecting the other end of this to the spore trap. After the collection the sample is analyzed to determine the spore types and quantities that are present within the cavity. This can be a useful indicator as to whether hidden mold sources are present within a cavity. However, a wall cavity sample is not always feasible. For example: an exterior wall with insulation inside of the cavity is not an ideal location for a wall cavity sample because the insulation fibers can cloud the sample and may make it unusable.

Mold sampling is an important part of performing a mold inspection of a property. However, sampling is not a tell all. Mold sampling should always be done in combination with a thorough physical inspection of the property in an effort to avoid false positives and/or false negatives. Additionally, both the inspection and the sampling should only be performed by a certified, professional microbial investigator. A good investigator will be certified to perform mold investigations and collect microbial samples, be able to think outside of the box and be diligent in examining specialty situations, and have background knowledge in areas like construction, water restoration, mold remediation and indoor air quality.

Brandon Apple

by Brandon Apple, Mold Inspection Sciences

February 18, 2014 at 1:00 pm

Fungal Data Interpretation – Part II – Effects of Tossing a Moldy Apple Pie into the Trash Before Mold Air Sampling

Moldy Apple Pie

This post is the second blog posting in a series based on information presented in a webinar by Dave Gallup, co-founder of EMLab P&K.  The topic of the webinar was Fungal Data Interpretation.  The two-hour presentation covered many interesting topics that are relevant to mold inspection and testing companies as well as the general public that are facing mold problems in their home or business.

One of the first points that Mr. Gallup made is the interpretation of the sample data that EMLab P&K provides must be combined with the on site mold inspection information.  Trying to interpret fungal sample data from a mold inspection and testing project without also having field inspection information from a qualified mold inspector is highly problematic.  In this blog entry I will focus on the second of several normal household scenarios that can drastically impact fungal sample data and could lead to incorrect interpretation of that data.

Scenario – “Effects of Tossing a Moldy Apple Pie into the Trash”

A group of EMLab P&K scientists studied the impact on fungal distribution in a normal home after the occupants tossed a mold apple pie into the kitchen trash.  Here is the data set:

  • The first air sample was collected in the home before tossing the moldy pie.
    • The air sample contained numerous types of mold spores.  I will focus on just one type, Penicillium/Aspergillus types (Pen/Asp).
    • The spore counts of Pen/Asp found in this first air sample were within “normal tolerances” — they were lower than the corresponding spore counts found in the outdoor baseline sample.
  • The second air sample was collected during the act of tossing the moldy pie
    • The spore counts of Pen/Asp were significantly elevated compared to both the outdoor control sample and the first sample collected before the toss.
    • This is how the data looked:
      • Pen/Asp types: before tossing ~13 spores/cubic meter | during tossing ~ 1,000,000 spores/cubic meter!

If the on site inspector did not notice that there was moldy food in the trashcan (apple pie in this case) or had not asked the homeowner if they had recently performed any housekeeping activities such as cleaning out the refrigerator of moldy food, incorrect conclusions could have been made with respect to this project.  For example the airborne Pen/Asp types prior to tossing were ~13 spores/cubic meter.  After tossing the moldy pie into the trash, the spore counts of Pen/Asp were drastically elevated (over one million spores/cubic meter!).  If the inspector did not know about the moldy food, these air sample results would be cause for real concern and unnecessary steps would likely follow (more testing, invasive exploration for mold, and the like).  Armed with the knowledge that the client recently threw away moldy food, the inspector could either take that into consideration when analyzing the sample data or, better, not collect the sample for several hours after.

Many people place too much emphasis on the mold sampling aspect of our business.  It is a useful tool, but it is only truly valuable in conjunction with the on site, visual inspection data.

Michael Bains

by Michael Bains, President, Mold Inspection Sciences

October 23, 2012 at 8:59 am 1 comment

Avoid Scare Tactics within the Mold Industry

Mold Scare Tactics

Unfortunately, there are a lot of “Scare Tactics” used within the microbial investigation and mold remediation industry. As with any industry, there are always going to be people out there who try and scare people into using their services. They may do so by embellishing facts, giving misinformation or by simply telling you things that are completely untrue. I want to give you, the consumer, a couple tips for what to watch out for if you are ever in a situation of having to enlist services within the microbial and mold remediation industry.

1) Pay close attention to each company’s website. Most companies have a website nowadays, and that can give you a good insight as to what type of company you will end up dealing with. Some companies websites are littered with misinformation and pictures geared towards scaring you into using their services. I have seen websites with embellished pictures of microscopic mold spores, but in reality just about anything looks scary when you magnify it 500 times. Also, if anywhere on their website you see the terms “Black Mold” or “Toxic Mold”, consider that a big red flag. Those terms were created by the media, and it wasn’t for their feel-good story of the evening if you know what I mean. It was to create interest as a result of fear. After all, who isn’t afraid of the term “toxic”?  You don’t hear many stories that start with toxic and end with a smile. You may also want to avoid companies that over emphasize the potential health effects of mold on people. Although it is good to be informed of potential signs of mold exposure and basic information regarding health, if a company’s main content of their website is to make you believe that you are definitely going to get sick after being around mold, it is probably another thing to be cautious of. And lastly, if somehow you have come across a company that does not even have a website, approach them with caution. If a company is not willing to provide basic information about them including their contact info, certification and affiliation information and a basic company profile it may be for good reason. They may be attempting to fly under the radar, or be quite new to the industry and have not yet put any effort into a website. I don’t know about you, but I don’t think I would trust a mold problem to the new guys on the block.

2) Be wary of remediation companies that do their own testing. Within our industry it is a direct conflict of interest for a remediation company to perform their own testing.  A large majority of the public has never dealt with a mold problem, or had to interpret a laboratory analysis of microbial samples.  Therefore, it could be somewhat easy for a remediation company to embellish sample results.  It is not uncommon to hear about a remediation company coming into a home and pulling some microbial samples, and upon receiving the results inform the client that the home is completely contaminated and they must vacate immediately or pay for expensive remediation. I had a client once tell me that a remediation company told her that she was being a bad mother because she was allowing her family to live in a mold infested home.  And that was based on a visual inspection alone.  Upon further investigation by an independent third party microbial investigator it was revealed that yes, they had a minimal mold problem but it was far less intense than the remediation company would have had her believe. You have to remember that a remediation company makes money off of cleaning up mold. Therefore, the more they have to clean or the larger the project, the more potential money they will make. So avoid being scared into expensive work that may not be needed and have an independent party look at the situation.

3) If you are ever in the middle of a microbial investigation and the inspector or contractor attempts to tell you what type of mold is present just by looking at it, be very cautious. I have heard multiple stories about contractors or inspectors coming in to look at a mold problem and attempting to identify what type of molds are present just by looking at it. Unfortunately, this is just not possible. There are literally tens of thousands of types of molds, many of them grow to be similar colors and textures and may display consistent growth patterns. The reality of it is, the only way to determine what type of mold is present is to analyze the growth under a high powered microscope, and this should only be done by a mycologist or technician within a laboratory setting. We hear about these tactics not only being used to scare people into remediation work that is not necessary, but also to deter people that really have a problem  from realizing it. For example, it is not uncommon for people in rental situations to be informed by maintenance personal that whatever microbial growth they have in their apartment or home is not the “bad kind”, or not toxic. I guess we would call this scenario an “Anti-Scare Tactic”. But again, the only way to know is to have microbial samples collected and properly analyzed. So unless the person you are dealing with just so happens to have microscopes for eyes, which would actually be pretty cool, watch out for this one.

If you really believe that you may have a mold problem, it is important to know that whomever you turn to for advice has your best interest in mind. The safest way to ensure this is to make sure that you always deal with an independent third party that has nothing to gain from finding a problem. You should also do all you can to research any companies that you may be considering using.  Make sure they are a legitimate company, they are properly certified and they should have a positive track record through organizations such as the Better Business Bureau.  You may be surprised what you find after doing a little investigation, for better or for worse.

Brandon Apple

by Brandon Apple, Mold Inspection Sciences

October 9, 2012 at 7:44 am 1 comment

Older Posts


Visit us on Facebook

Follow us on Twitter

Contact Mold Inspection Sciences

Phoenix - 602.247.8681
Los Angeles - 310.451.9333
Orange County - 949.892.6343
San Diego - 619.618.2885
Seattle/Tacoma - 206.407.3352
Portland/Vancouver - 503.922.3399
Denver/Boulder - 303.339.0133
Cincinnati - 513.448.1253
Austin - 512.535.2493
Dallas/Fort Worth - 214.774.4380
San Antonio - 210.568.7725
Houston - 281.652.5353
www.moldsci.com